View ISL22446_711431.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
ISL22446
Quad Digitally Controlled Potentiometer (XDCPTM)
Data Sheet July 17, 2006 FN6181.0
Low Noise, Low Power, SPI(R) Bus, 128 Taps
The ISL22446 integrates four digitally controlled potentiometers (DCP) and non-volatile memory on a monolithic CMOS integrated circuit. The digitally controlled potentiometers are implemented with a combination of resistor elements and CMOS switches. The position of the wipers are controlled by the user through the SPI serial interface. Each potentiometer has an associated volatile Wiper Register (WR) and a non-volatile Initial Value Register (IVR) that can be directly written to and read by the user. The contents of the WR controls the position of the wiper. At power-up the device recalls the contents of the DCP's IVR to the corresponding WR. The DCPs can be used as three-terminal potentiometers or as two-terminal variable resistors in a wide variety of applications including control, parameter adjustments, and signal processing.
Features
* Four potentiometers in one package * 128 resistor taps * SPI serial interface * Non-volatile storage of wiper position * Wiper resistance: 70 typical @ 3.3V * Shutdown mode * Shutdown current 5A max * Power supply: 2.7V to 5.5V * 50k or 10k total resistance * High reliability - Endurance: 1,000,000 data changes per bit per register - Register data retention: 50 years @ T <55C * 20 Lead TSSOP * Pb-free plus anneal product (RoHS compliant)
Pinout
ISL22446 (20 LD TSSOP) TOP VIEW
RH3 RL3 RW3 NC SCK SDO GND RW2 RL2 RH2 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 RW0 RL0 RH0 SHDN VCC SDI CS RH1 RL1 RW1
Ordering Information
PART NUMBER ISL22446UFV20Z (Notes 1, 2) ISL22446WFV20Z (Notes 1, 2) NOTES: 1. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2. Add "-TK" suffix for 1,000 Tape and Reel option PART MARKING 22446 UFVZ 22446 WFVZ RESISTANCE OPTION (k) 50 10 TEMP. RANGE (C) -40 to +125 -40 to +125 PACKAGE 20 Ld TSSOP (Pb-free) 20 Ld TSSOP (Pb-free) PKG. DWG. # M20.173 M20.173
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) and XDCP are registered trademarks of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners.
ISL22446 Block Diagram
VCC RH3 SCK SDI SDO CS SPI INTERFACE POWER UP INTERFACE, CONTROL AND STATUS LOGIC
WR3
RW3 RL3 RH2
WR2
RW2 RL2 RH1
WR1
SHDN NONVOLATILE REGISTERS
RW1 RL1 RH0
WR0
RW0 RL0
GND
Pin Descriptions
TSSOP PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 SYMBOL RH3 RL3 RW3 NC SCK SDO GND RW2 RL2 RH2 RW1 RL1 RH1 CS SDI VCC SHDN RH0 RL0 RW0 SPI clock input SPI Open drain Data Output Device ground pin "Wiper" terminal of DCP2 "Low" terminal of DCP2 "High" terminal of DCP2 "Wiper" terminal of DCP1 "Low" terminal of DCP1 "High" terminal of DCP1 SPI Chip Select active low input SPI Data Input Power supply pin Shutdown active low input "High" terminal of DCP0 "Low" terminal of DCP0 "Wiper" terminal of DCP0 "High" terminal of DCP3 "Low" terminal of DCP3 "Wiper" terminal of DCP3 DESCRIPTION
2
FN6181.0 July 17, 2006
ISL22446
Absolute Maximum Ratings
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Voltage at any Digital Interface Pin with Respect to GND . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC+0.3 VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V Voltage at any DCP pin with Respect to GND . . . . . . . -0.3V to VCC Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . . . 300C IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6mA Latchup (Note 4) . . . . . . . . . . . . . . . . . . Class II, Level B @ +125C ESD (HBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5kV (CDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1k
Thermal Information
Thermal Resistance (Typical, Note 3) 20 Lead TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . JA (C/W) 90
Recommended Operating Conditions
Temperature Range (Extended Industrial). . . . . . . .-40C to +125C Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150C VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0mA
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES: 3. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 4. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using a max negative pulse of -0.8V for all pins.
Analog Specifications
SYMBOL RTOTAL
Over recommended operating conditions unless otherwise stated. TEST CONDITIONS W option U option MIN TYP (NOTE 5) 10 50 -20 50 80 0 70 10/10/25 Voltage at pin from GND to VCC 0.1 1 VCC 200 +20 MAX UNIT k k % ppm/C (Note 21) ppm/C (Note 21) V pF A
PARAMETER RH to RL resistance
RH to RL resistance tolerance End-to-End Temperature Coefficient
W and U option W option U option
VRH, VRL RW CH/CL/CW (Note 21) ILkgDCP
VRH and VRL Terminal Voltages Wiper resistance Potentiometer capacitance Leakage on DCP pins
VRH and VRL to GND VCC = 3.3V @ +25C, wiper current = VCC/RTOTAL
VOLTAGE DIVIDER MODE (0V @ RLi; VCC @ RHi; measured at RWi, unloaded; i = 0, 1, 2 or 3) INL (Note 10) DNL (Note 9) ZSerror (Note 7) FSerror (Note 8) VMATCH (Note 11) TCV (Note 12) Integral non-linearity Differential non-linearity Zero-scale error Monotonic over all tap positions Monotonic over all tap positions W option U option Full-scale error W option U option DCP to DCP matching Any two DCPs at same tap position, same voltage at all RH terminals, and same voltage at all RL terminals DCP register set to 40 hex -1 -0.5 0 0 -5 -2 -2 1 0.5 -1 -1 1 0.5 5 2 0 0 2 LSB (Note 6) LSB (Note 6) LSB (Note 6) LSB (Note 6) LSB (Note 6) ppm/C
Ratiometric temperature coefficient
4
RESISTOR MODE (Measurements between RWi and RLi with RHi not connected, or between RWi and RHi with RLi not connected; i = 0, 1, 2 or 3) RINL (Note 16) Integral non-linearity DCP register set between 10h and 7Fh; monotonic over all tap positions -1 1 MI (Note 13)
3
FN6181.0 July 17, 2006
ISL22446
Analog Specifications
SYMBOL RDNL (Note 15) Roffset (Note 14) Over recommended operating conditions unless otherwise stated. (Continued) TEST CONDITIONS DCP register set between 10h and 7Fh; monotonic over all tap positions W option U option RMATCH (Note 17) DCP to DCP matching Any two DCPs at the same tap position with the same terminal voltages MIN -0.5 0 0 -2 1 0.5 TYP (NOTE 5) MAX 0.5 7 2 2 UNIT MI (Note 13) MI (Note 13) MI (Note 13) MI (Note 13)
PARAMETER Differential non-linearity Offset
Operating Specifications Over the recommended operating conditions unless otherwise specified.
SYMBOL ICC1 ICC2 ISB PARAMETER VCC supply current (volatile write/read) VCC supply current (non-volatile write/read) VCC current (standby) TEST CONDITIONS fSCK = 5MHz; (for SPI Active, Read and Volatile Write states only) fSCK = 5MHz; (for SPI Active, Read and Non-volatile Write states only) VCC = +5.5V @ +85C, SPI interface in standby state VCC = +5.5V @ +125C, SPI interface in standby state VCC = +3.6V @ +85C, SPI interface in standby state VCC = +3.6V @ +125C, SPI interface in standby state ISD VCC current (shutdown) VCC = +5.5V @ +85C, SPI interface in standby state VCC = +5.5V @ +125C, SPI interface in standby state VCC = +3.6V @ +85C, SPI interface in standby state VCC = +3.6V @ +125C, SPI interface in standby state ILkgDig tWRT (Note 21) tShdnRec (Note 21) Leakage current at pins SHDN, SCK, SDI, SDO and CS Wiper Response Time after SPI write to WR register DCP recall time from shutdown mode From rising edge of SHDN signal to wiper stored position and RH connection SCK rising edge of last bit of ACR data byte to wiper stored position and RH connection Vpor VccRamp tD Power-on recall voltage Vcc ramp rate Power-up delay VCC above Vpor, to DCP Initial Value Register recall completed, and SPI Interface in standby state Minimum VCC at which memory recall occurs 2.0 0.2 3 Voltage at pin from GND to VCC -1 1.5 1.5 1.5 2.6 MIN TYP (NOTE 5) MAX 0.5 3 5 7 3 5 3 5 2 4 1 UNIT mA mA A A A A A A A A A s s s V V/ms ms
EEPROM SPECIFICATION EEPROM Endurance EEPROM Retention Temperature T <55C 1,000,000 50 Cycles Years
FN6181.0 July 17, 2006
4
ISL22446
Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued)
SYMBOL tWC (Note 19) PARAMETER Non-volatile Write cycle time TEST CONDITIONS MIN TYP (NOTE 5) 12 MAX 20 UNIT ms
SERIAL INTERFACE SPECIFICATIONS VIL VIH Hysteresis VOL Rpu (Note 20) Cpin (Note 21) fSCK tCYC tWH tWL tLEAD tLAG tSU tH tRI tFI tDIS tV tHO tRO tFO tCS NOTES: 5. Typical values are for TA = +25C and 3.3V supply voltage. 6. LSB: [V(RW)127 - V(RW)0]/127. V(RW)127 and V(RW)0 are V(RW) for the DCP register set to 7F hex and 00 hex respectively. LSB is the incremental voltage when changing from one tap to an adjacent tap. 7. ZS error = V(RW)0/LSB. 8. FS error = [V(RW)127 - VCC]/LSB. 9. DNL = [V(RW)i - V(RW)i-1]/LSB-1, for i = 1 to 127. i is the DCP register setting. 10. INL = [V(RW)i - i * LSB - V(RW)]/LSB for i = 1 to 127 11. VMATCH = [V(RWx)i - V(RWy)i]/LSB, for i = 1 to 127, x = 0 to 3 and y = 0 to 3. Max ( V ( RW ) i ) - Min ( V ( RW ) i ) 10 6 12. TC = --------------------------------------------------------------------------------------------- x ---------------- for i = 16 to 112 decimal, T = -40C to +125C. Max( ) is the maximum value of the wiper V [ Max ( V ( RW ) i ) + Min ( V ( RW ) i ) ] 2 165C voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range. 13. MI = |RW127 - RW0|/127. MI is a minimum increment. RW127 and RW0 are the measured resistances for the DCP register set to 7F hex and 00 hex respectively. SHDN, SCK, SDI, and CS input buffer LOW voltage SHDN, SCK, SDI, and CS input buffer HIGH voltage SHDN, SCK, SDI, and CS input buffer hysteresis SDO output buffer LOW voltage SDO pull-up resistor off-chip SHDN, SCK, SDI, SDO and CS pin capacitance SPI frequency SPI clock cycle time SPI clock high time SPI clock low time Lead time Lag time SDI, SCK and CS input setup time SDI, SCK and CS input hold time SDI, SCK and CS input rise time SDI, SCK and CS input fall time SDO output Disable time SDO output valid time SDO output hold time SDO output rise time SDO output fall time CS deselect time Rpu = 2k, Cb = 30pF Rpu = 2k, Cb = 30pF 2 0 60 60 200 100 100 250 250 50 50 10 10 0 20 100 350 IOL = 4mA Maximum is determined by tRO and tFO with maximum bus load Cb = 30pF, fSCK = 5MHz 10 5 -0.3 0.7*VCC 0.05* VCC 0 0.4 2 0.3*VCC VCC+0.3 V V V V k pF MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns s
5
FN6181.0 July 17, 2006
ISL22446
14. Roffset = RW0/MI, when measuring between RW and RL. Roffset = RW127/MI, when measuring between RW and RH. 15. RDNL = (RWi - RWi-1)/MI -1, for i = 16 to 127. 16. RINL = [RWi - (MI * i) - RW0]/MI, for i = 16 to 127. 17. RMATCH = (RWi,x - RWi,y)/MI, for i = 1 to 127, x = 0 to 3 and y = 0 to 3. 6 for i = 16 to 112, T = -40C to +125C. Max( ) is the maximum value of the resistance and Min ( ) is 18. [ Max ( Ri ) - Min ( Ri ) ] 10 TC R = --------------------------------------------------------------- x ---------------- the minimum value of the resistance over the temperature range. [ Max ( Ri ) + Min ( Ri ) ] 2 165C 19. tWC is the time from the end of a Write sequence of SPI serial interface, to the end of the self-timed internal non-volatile write cycle. 20. Rpu is specified for the highest data rate transfer for the device. Higher value pullup can be used at lower data rates. 21. This parameter is not 100% tested.
Timing Diagrams
Input Timing
tCS CS tLEAD SCK tSU SDI MSB tH tWL tCYC tLAG
...
tWH
tFI LSB
tRI
...
SDO
HIGH IMPEDANCE
Output Timing
CS
SCK tV SDO MSB tHO
...
tDIS
...
LSB
SDI
ADDR
XDCP Timing (for All Load Instructions)
CS
SCK
...
tWRT MSB
SDI
...
LSB
VW
SDO
HIGH IMPEDANCE
6
FN6181.0 July 17, 2006
ISL22446 Typical Performance Curves
VCC
100 90
WIPER RESISITANCE ()
Vcc = 3.3V, T = 125C
1.4
80 70 60 50 40 30 20 10 0 0 20 40 60 80 100 120
TAP POSITION (DECIMAL)
1.2 T =125 C 1
VCC
Isb (A)
0.8
0.6
Vcc = 3.3V, T = 20C
Vcc = 3.3V, T = -40C
0.4 T =25 C 0.2
0 2.7 3.2 3.7 4.2 4.7 5.2
Vcc, V
FIGURE 2. STANDBY ICC vs VCC
FIGURE 1. WIPER RESISTANCE vs TAP POSITION [ I(RW) = VCC/RTOTAL ] FOR 10k (W)
0.2 Vcc = 2.7V 0.1
DNL (LSB) INL (LSB)
0.2
T = 25C
T = 25C 0.1 Vcc = 2.7V
0
0
-0.1 Vcc = 5.5V -0.2 0 20 40 60 80 100 120
TAP POSITION (DECIMAL)
-0.1 Vcc = 5.5V -0.2 0 20 40 60 80 100 120
TAP POSITION (DECIMAL)
FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR 10k (W)
FIGURE 4. INL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR 10k (W)
1.30 1.10 0.90
ZSerror (LSB)
0.00
10k
-0.30 Vcc = 2.7V
FSerror (LSB)
50k
Vcc = 5.5V
0.70 0.50 0.30 0.10 -0.10 -0.30 -40 -20 0 50k Vcc = 5.5V Vcc = 2.7V
-0.60 -0.90 10k -1.20 -1.50 -40
20
40
60
80
100
120
-20
0
20
40
60
80
100
120
TEMPERATURE (C)
TEMPERATURE (C)
FIGURE 5. ZSerror vs TEMPERATURE
FIGURE 6. FSerror vs TEMPERATURE
7
FN6181.0 July 17, 2006
ISL22446 Typical Performance Curves
0.4 0.2
DNL (LSB) INL (LSB)
(Continued)
0.4
T=25C
0.2 0
T = 25C
0 -0.2 Vcc =2.7V -0.4 -0.6 16 Vcc =5.5V
Vcc = 5.5V -0.2 Vcc = 2.7V -0.4 -0.6
36
56
76
96
116
16
36
56
76
96
116
TAP PO SITIO (DECIMAL) N
TAP POSITION (DECIMAL)
FIGURE 7. DNL vs TAP POSITION IN Rheostat MODE FOR 10k (W)
FIGURE 8. INL vs TAP POSITION IN Rheostat MODE FOR 10k (W)
END TO END RTOTAL CHANGE (%)
1.00 Vcc = 2.7V 0.50
TCv (ppm/C)
105
50k
90 75 60 45 30 15 0
10k
0.00
-0.50 Vcc = 5.5V -1.00 -40 10k
50k
-20
0
20
40
60
80
100
120
16
36
56
76
96
TEMPERATURE (C)
TAP POSITION (DECIM AL)
FIGURE 9. END TO END RTOTAL % CHANGE vs TEMPERATURE
FIGURE 10. TC FOR VOLTAGE DIVIDER MODE IN ppm
INPUT
300 250
TCr (ppm/C)
OUTPUT
200 150 100 50 0 16
10k
50k
Wiper at Mid Point (position 40h) Rtotal = 9.5k
36
56
76
96
TAP POSITION (DECIMAL)
FIGURE 11. TC FOR Rheostat MODE IN ppm
FIGURE 12. FREQUENCY RESPONSE (2.6MHz)
8
FN6181.0 July 17, 2006
ISL22446 Typical Performance Curves
(Continued)
Wiper Mid Point Movement from 3Fh to 40h
FIGURE 13. MIDSCALE GLITCH, CODE 3Fh TO 40h
FIGURE 14. LARGE SIGNAL SETTLING TIME
Pin Description
Potentiometers Pins
RHi and RLi (i = 0, 1, 2, 3) The high (RHi) and low (RLi) terminals of the ISL22446 are equivalent to the fixed terminals of a mechanical potentiometer. RHi and RLi are referenced to the relative position of the wiper and not the voltage potential on the terminals. With WRi set to 127 decimal, the wiper will be closest to RHi, and with the WRi set to 0, the wiper is closest to RLi. RWi (i = 0, 1, 2, 3) RWi is the wiper terminal and is equivalent to the movable terminal of a mechanical potentiometer. The position of the wiper within the array is determined by the WRi register. SHDN The SHDN pin forces the resistor to end-to-end open circuit condition on RHi and shorts RWi to RLi. When SHDN is returned to logic high, the previous latch settings put RWi at the same resistance setting prior to shutdown. This pin is logically OR'd with SHDN bit in ACR register. SPI interface is still available in shutdown mode and all registers are accessible. This pin must remain HIGH for normal operation.
RHi
Bus Interface Pins
Serial Clock (SCK) This is the serial clock input of the SPI serial interface. Serial Data Output (SDO) The SDO is an open drain serial data output pin. During a read cycle, the data bits are shifted out at the falling edge of the serial clock SCK, while the CS input is low. SDO requires an external pull-up resistor for proper operation. Serial Data Input (SDI) The SDI is the serial data input pin for the SPI interface. It receives device address, operation code, wiper address and data from the SPI external host device. The data bits are shifted in at the rising edge of the serial clock SCK, while the CS input is low. Chip Select (CS) CS LOW enables the ISL22446, placing it in the active power mode. A HIGH to LOW transition on CS is required prior to the start of any operation after power up. When CS is HIGH, the ISL22446 is deselected and the SDO pin is at high impedance, and (unless an internal write cycle is underway) the device will be in the standby state.
Principles of Operation
The ISL22446 is an integrated circuit incorporating four DCPs with its associated registers, non-volatile memory and the SPI serial interface providing direct communication between host and potentiometers and memory. The resistor array is comprised of individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the potential at that point to the wiper.
RWi
RLi
FIGURE 15. DCP CONNECTION IN SHUTDOWN MODE
9
FN6181.0 July 17, 2006
ISL22446
The electronic switches on the device operate in a "make before break" mode when the wiper changes tap positions. When the device is powered down, the last value stored in IVRi will be maintained in the non-volatile memory. When power is restored, the contents of the IVRi is recalled and loaded into the corresponding WRi to set the wiper to the initial value.
TABLE 1. MEMORY MAP ADDRESS 6 5 4 3 2 1 0 NON-VOLATILE General Purpose General Purpose General Purpose IVR3 IVR2 IVR1 IVR0 VOLATILE Not Available Not Available Not Available WR3 WR2 WR1 WR0
DCP Description
Each DCP is implemented with a combination of resistor elements and CMOS switches. The physical ends of each DCP are equivalent to the fixed terminals of a mechanical potentiometer (RH and RL pins). The RW pin of each DCP is connected to intermediate nodes, and is equivalent to the wiper terminal of a mechanical potentiometer. The position of the wiper terminal within the DCP is controlled by volatile Wiper Register (WR). Each DCP has its own WR. When the WR of a DCP contains all zeroes (WR[6:0]= 00h), its wiper terminal (RW) is closest to its "Low" terminal (RL). When the WR register of a DCP contains all ones (WR[6:0]= 7Fh), its wiper terminal (RW) is closest to its "High" terminal (RH). As the value of the WR increases from all zeroes (0) to all ones (127 decimal), the wiper moves monotonically from the position closest to RL to the closest to RH. At the same time, the resistance between RW and RL increases monotonically, while the resistance between RH and RW decreases monotonically. While the ISL22446 is being powered up, all four WRs are reset to 40h (64 decimal), which locates RW roughly at the center between RL and RH. After the power supply voltage becomes large enough for reliable non-volatile memory reading, all WRs will be reload with the value stored in corresponding non-volatile Initial Value Registers (IVRs). The WRs can be read or written to directly using the SPI serial interface as described in the following sections. The SPI interface register address bits have to be set to 0000b, 0001b, 0010b or 0011b to access the WR of DCP0, DCP1, DCP2 or DCP3 respectively. The WRi and IVRi can be read or written to directly using the SPI serial interface as described in the following sections.
The non-volatile IVRi and volatile WRi registers are accessible with the same address. The Access Control Register (ACR) contains information and control bits described below in Table 2. The VOL bit (ACR[7]) determines whether the access is to wiper registers WR or initial value registers IVR.
TABLE 2. ACCESS CONTROL REGISTER (ACR) BIT #
Bit Name
7
VOL
6
SHDN
5
WIP
4 0
3 0
2 0
1 0
0 0
If VOL bit is 0, the non-volatile IVR register is accessible. If VOL bit is 1, only the volatile WR is accessible. Note, value is written to IVR register also is written to the WR. The default value of this bit is 0. The SHDN bit (ACR[6]) disables or enables Shutdown mode. This bit is logically OR'd with SHDN pin. When this bit is 0, DCP is in Shutdown mode. Default value of SHDN bit is 1. The WIP bit (ACR[5]) is read only bit. It indicates that nonvolatile write operation is in progress. The WIP bit can be read repeatedly after a non-volatile write to determine if the write has been completed. It is impossible to write to the IVRi, WRi or ACR while WIP bit is 1.
SPI Serial Interface
The ISL22446 supports an SPI serial protocol, mode 0. The device is accessed via the SDI input and SDO output with data clocked in on the rising edge of SCK, and clocked out on the falling edge of SCK. CS must be LOW during communication with the ISL22446. SCK and CS lines are controlled by the host or master. The ISL22446 operates only as a slave device. All communication over the SPI interface is conducted by sending the MSB of each byte of data first.
Memory Description
The ISL22446 contains seven non-volatile and five volatile 8-bit registers. The memory map of ISL22446 is on Table 1. The four non-volatile registers (IVRi) at address 0, 1, 2 and 3, contain initial wiper value and volatile registers (WRi) contain current wiper position. In addition, three non-volatile General Purpose registers from address 4 to address 6 are available.
TABLE 1. MEMORY MAP ADDRESS 8 7 NON-VOLATILE -- Reserved VOLATILE ACR
10
FN6181.0 July 17, 2006
ISL22446
Protocol Conventions
The first byte sent to the ISL22446 from the SPI host is the Identification Byte. A valid Identification Byte contains 0101 as the four MSBs, with the following four bits set to 0.
TABLE 3. IDENTIFICATION BYTE FORMAT 0 (MSB) 1 0 1 0 0 0 0 (LSB)
after reaching the address 0110b, the internal pointer "rolls over" to address 0000b. The internal non-volatile write cycle starts after rising edge of CS and takes up to 20ms. Thus, non-volatile registers must be written individually.
Read Operation
A read operation to the ISL22446 is a three-byte operation. It requires first, the CS transition from HIGH to LOW, then a valid Identification Byte, then a valid instruction byte following by "dummy" Data Byte is sent to SDI pin. The SPI host reads the data from SDO pin on falling edge of SCK. The host terminates the read operation by pulling the CS pin from LOW to HIGH (see Figure 17). The ISL22446 will provide the Data Bytes to the SDO pin as long as SCK is provided by the host from the registers indicated by an internal pointer. This pointer initial value is determined by the register address in the Read operation instruction, and increments by one during transmission of each Data Byte. After reaching the memory location 0110b, the pointer "rolls over" to 0000b, and the device continues to output the data for each received SCK clock. In order to read back the non-volatile IVR, it is recommended that the application reads the ACR first to verify the WIP bit is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat its reading sequence again.
The next byte sent to the ISL22446 contains the instruction and register pointer information. The four MSBs are the instruction and four LSBs are register address (see Table 4).
TABLE 4. IDENTIFICATION BYTE FORMAT 7 I3 6 I2 5 I1 4 I0 3 R3 2 R2 1 R1 0 R0
There are only two valid instruction sets: 1011(binary) - is a Read operation 1100(binary) - is a Write operation
Write Operation
A Write operation to the ISL22446 is a three-byte operation. It requires first, the CS transition from HIGH to LOW, then a valid Identification Byte, then a valid instruction byte following by Data Byte is sent to SDI pin. The host terminates the write operation by pulling the CS pin from LOW to HIGH. For a write to addresses 0000b to 0011b, the MSB at address 8 (ACR[7]) determines if the Data Byte is to be written to volatile or both volatile and non-volatile registers. Refer to "Memory Description" and Figure 16. Device can receive more than one byte of data by auto incrementing the address after each received byte. Note
CS
SCK
SDI 0 1 0 1 0 0 0 0 0 I3 I2 I1 I0 R3 R2 R1 R0 0 D6 D5 D4 D3 D2 D1 D0
FIGURE 16. THREE BYTE WRITE SEQUENCE
CS
SCK
SDI 0 SDO 0 1 0 1 0 0 0 0 0 I3 I2 I1 I0 R3 R2 R1 R0
DON'T CARE
D6 D5 D4
D3
D2
D1 D0
FIGURE 17. THREE BYTE READ SEQUENCE
11
FN6181.0 July 17, 2006
ISL22446 Applications Information
Communicating with ISL22446
Communication with ISL22446 proceeds using SPI interface through the ACR (address 1000b), IVRi (addresses 0000b, 0001b, 0010b and 0011b) and WRi (addresses 0000b, 0001b, 0010b and 0011b) registers. The wiper of the potentiometer is controlled by the WRi register. Writes and reads can be made directly to these registers to control and monitor the wiper position without any non-volatile memory changes. This is done by setting MSB bit at address 1000b to 1. The non-volatile IVRi stores the power up value of the wiper. IVRs are accessible when MSB bit at address 1000b is set to 0. Writing a new value to the IVRi register will set a new power up position for the wiper. Also, writing to this register will load the same value into the corresponding WRi as the IVRi. Reading from the IVRi will not change the WRi, if its contents are different.
Examples:
A. Writing to the IVR:
This sequence will write a new value (77h) to the IVR2(non-volatile): Set the ACR (Addr 1000b) for NV write (40h) Send the ID byte, Instruction Byte, then the Data byte 010100001100100 Set the IVR (Addr 0010b) to 77h Send the ID byte, Instruction Byte, then the Data byte 010100001100001
0
0100 (Sent to SDI)
0
0
0
0
0
0111 (Sent to SDI)
0
1
1
1
B. Reading from the WR:
This : sequence will read the value from the WR3 (volatile): Write to ACR first to access the volatile WRs Send the ID byte, Instruction Byte, then the Data byte 010100001100100
0
1100 (Sent to SDI)
0
0
0
0
Read the data from WR3 (Addr 0011b) Send the ID byte, Instruction Byte, then Read the Data byte 0101000010110011xxxxx (Out on SDO)
x
x
x
12
FN6181.0 July 17, 2006
ISL22446 Thin Shrink Small Outline Plastic Packages (TSSOP)
N INDEX AREA E E1 -B1 2 3 0.05(0.002) -AD -CSEATING PLANE A 0.25 0.010 L 0.25(0.010) M GAUGE PLANE BM
M20.173
20 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A A1 A2 b c D MIN 0.002 0.031 0.0075 0.0035 0.252 0.169 0.246 0.0177 20 0o 8o 0o MAX 0.047 0.006 0.051 0.0118 0.0079 0.260 0.177 0.256 0.0295 MILLIMETERS MIN 0.05 0.80 0.19 0.09 6.40 4.30 6.25 0.45 20 8o MAX 1.20 0.15 1.05 0.30 0.20 6.60 4.50 6.50 0.75 NOTES 9 3 4 6 7 Rev. 1 6/98
e
b 0.10(0.004) M C AM BS
A1 0.10(0.004)
A2 c
E1 e E L N
0.026 BSC
0.65 BSC
NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AC, Issue E. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E1" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of "b" dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 13
FN6181.0 July 17, 2006

▲Up To Search▲

Price & Availability of ISL22446

	To Download ISL22446 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .